TP-LINK TL-SG2210P Guide de l'utilisateur Page 98
- Page / 188
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Router Port: Displays the router po
rt of the VLAN.
Note:
The settings here will be invalid when multicast VLAN is enabled
Configuration procedure:
Step Operation Description
1 Enable IGMP Snooping
function
Required. Enable IGMP Snooping globally on the switch
and for the port on Multicast→IGMP
Snooping→Snooping Config and Port Config page.
2 Configure the multicast
parameters for VLANs
Optional. Configure the multicast parameters for VLANs
on Multicast→IGMP Snooping→VLAN Config page.
If a VLAN has no multicast parameters configuration, it
indicates the IGMP Snooping is not enabled in the VLAN,
thus the multicast data in the VLAN will be broadcasted.
8.1.4 Multicast VLAN
In old multicast transmission mode, when users in different VLANs apply for join the same
multicast group, the multicast router will duplicate this multicast information and deliver each
VLAN owning a receiver one copy. This mode wastes a lot of bandwidth.
The problem above can be solved by configuring a multicast VLAN. By adding switch ports to the
multicast VLAN and enabling IGMP Snooping, you can make users in different VLANs share the
same multicast VLAN. This saves the bandwidth since multicast streams are transmitted only
within the multicast VLAN and also guarantees security because the multicast VLAN is isolated
from user VLANS.
Before configuring a multicast VLAN, you should firstly configure a VLAN as multicast VLAN and
add the corresponding ports to the VLAN on the 802.1Q VLAN page. If the multicast VLAN is
enabled, the multicast configuration for other VLANs on the VLAN Config page will be invalid, that
is, the multicast streams will be transmitted only within the multicast VLAN.
Choose the menu Multicast→IGMP Snooping→Multicast VLAN to load the following page.
Figure 8-7 Multicast VLAN
90
- Gigabit Smart Switch 1
- COPYRIGHT & TRADEMARKS 2
- FCC STATEMENT 2
- CE Mark Warning 2
- Safety Information 3
- Package Contents 9
- Chapter 1 About this Guide 10
- Chapter 2 Introduction 14
- 2.3.2 Rear Panel 18
- 3.1 Login 20
- 3.2 Configuration 20
- Chapter 4 System 22
- 4.1.2 Device Description 23
- 4.1.3 System Time 24
- 4.1.4 Daylight Saving Time 25
- 4.1.5 System IP 26
- 4.2 User Management 27
- 4.2.2 User Config 28
- 4.3 System Tools 29
- 4.3.2 Config Backup 30
- 4.3.3 Firmware Upgrade 30
- 4.3.4 System Reboot 31
- 4.3.5 System Reset 31
- 4.4 Access Security 32
- 4.4.2 SSL Config 33
- Certificate Download 34
- Key Download 34
- 4.4.3 SSH Config 35
- Chapter 5 Switching 41
- 5.1.2 Port Mirror 42
- Mirror Group List 43
- Mirror Group 43
- Mirroring Port 43
- 5.1.3 Port Security 44
- Port Security 45
- 5.1.4 Port Isolation 46
- 5.1.5 Loopback Detection 47
- 5.2 LAG 48
- 5.2.1 LAG Table 49
- 5.2.2 Static LAG 50
- 5.2.3 LACP Config 51
- Figure 5-10 LACP Config 52
- 5.3 Traffic Monitor 53
- 5.3.2 Traffic Statistics 54
- 5.4 MAC Address 55
- 5.4.1 Address Table 56
- 5.4.2 Static Address 57
- 5.4.3 Dynamic Address 58
- Aging Config 59
- Search Option 59
- Dynamic Address Table 59
- 5.4.4 Filtering Address 60
- 5.5 DHCP Filtering 61
- DHCP Cheating Attack 63
- DHCP Filtering 64
- Trusted Port 64
- Chapter 6 VLAN 65
- 6.1 802.1Q VLAN 66
- 6.1.1 VLAN Config 67
- VLAN Create 68
- VLAN Table 68
- VLAN Membership 68
- Configure Switch B 70
- Chapter 7 Spanning Tree 71
- STP Timers 72
- STP Generation 72
- In the beginning 72
- Comparing BPDUs 73
- Selecting the root bridge 73
- MSTP 75
- Port States 75
- Port Roles 75
- 7.1 STP Config 76
- Parameters Config 77
- 7.2 Port Config 78
- Port Config 79
- 7.3 MSTP Instance 80
- 7.3.2 Instance Config 81
- 7.3.3 Instance Port Config 82
- 7.4 STP Security 84
- TC Protect 85
- BPDU Protect 85
- BPDU Filter 85
- 7.4.2 TC Protect 86
- Figure 7-11 TC Protect 87
- Configure Switch A: 88
- Configure Switch B: 88
- Configure Switch C: 89
- Configure Switch D: 89
- Chapter 8 Multicast 91
- Multicast Address 92
- Multicast Address Table 92
- 8.1 IGMP Snooping 93
- 8.1.1 Snooping Config 94
- 8.1.2 Port Config 95
- 8.1.3 VLAN Config 96
- VLAN Config 97
- 8.1.4 Multicast VLAN 98
- Configuration procedure: 99
- Network Requirements 100
- 8.2 Multicast IP 101
- 8.2.1 Multicast IP Table 102
- 8.2.2 Static Multicast IP 102
- 8.3 Multicast Filter 103
- 8.3.1 IP-Range 104
- 8.3.2 Port Filter 104
- Configuration Procedure: 105
- 8.4 Packet Statistics 106
- Chapter 9 QoS 108
- Figure 9-2 802.1Q frame 109
- Figure 9-3 IP datagram 109
- Figure 9-4 SP-Mode 110
- Figure 9-5 WRR-Mode 110
- 9.1 DiffServ 111
- 9.1.2 802.1P/CoS mapping 113
- 9.1.3 DSCP Priority 114
- 9.1.4 Schedule Mode 116
- 9.2 Bandwidth Control 117
- 9.2.2 Storm Control 118
- 9.3 Voice VLAN 120
- Port Voice VLAN Mode 121
- 9.3.1 Global Config 122
- 9.3.2 Port Config 123
- 9.3.3 OUI Config 124
- Chapter 10 ACL 126
- 10.1.3 MAC ACL 127
- 10.1.4 Standard-IP ACL 128
- 10.1.5 Extend-IP ACL 128
- 10.2 Policy Config 129
- 10.2.1 Policy Summary 130
- 10.2.2 Policy Create 130
- 10.3 Policy Binding 131
- 10.3.2 Port Binding 132
- 10.3.3 VLAN Binding 132
- Network Diagram 134
- Configuration Procedure 134
- Chapter 11 PoE 136
- 11.1.1 PoE Config 137
- Global Config 138
- 11.1.2 PoE Profile 139
- 11.2 PoE Time-Range 140
- 11.2.1 Time-Range Summary 141
- 11.2.3 PoE Holiday Config 142
- Create Holiday 143
- Holiday Table 143
- Chapter 12 SNMP 144
- MIB Introduction 145
- 12.1 SNMP Config 146
- 12.1.2 SNMP View 147
- 12.1.3 SNMP Group 148
- 12.1.4 SNMP User 149
- User Config 150
- User Table 150
- 12.1.5 SNMP Community 151
- 12.2 Notification 153
- 12.3 RMON 154
- 12.3.1 History Control 155
- 12.3.2 Event Config 156
- 12.3.3 Alarm Config 157
- Chapter 13 LLDP 159
- 13.1 Basic Config 163
- 13.1.2 Port Config 164
- 13.2 Device Info 165
- 13.3 Device Statistics 166
- Auto Refresh 167
- Global Statistics 167
- Neighbor Statistics 167
- 13.4 LLDP-MED 168
- 13.4.1 Global Config 169
- 13.4.2 Port Config 169
- LLDP-MED Port Config 170
- 13.4.3 Local Info 171
- 13.4.4 Neighbor Info 172
- Neighbor Info 173
- Chapter 14 Maintenance 174
- 14.2 Log 175
- 14.2.1 Log Table 176
- 14.2.2 Local Log 177
- 14.2.3 Remote Log 177
- 14.2.4 Backup Log 178
- 14.3 Device Diagnostics 179
- 14.4 Network Diagnostics 180
- 14.4.2 Tracert 181
- Tracert Config 182
- Appendix A: Specifications 183
- Appendix C: Glossary 186
Produits connexes et manuels pour Commutateurs de réseau TP-LINK TL-SG2210P
(16 pages)© 2020, manymanuals.fr. Tous droits réservés | 1.516 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels