TP-LINK T3700G-28TQ Guide d'installation Page 1

Installation GuideStackable L2+ Managed SwitchT2700G-28TQBusiness Networking SolutionStackable L3 Managed SwitchT3700G-28TQ

05 Stackable L2+/L3 Managed SwitchChapter 2 Preparing For Installation2.1 Package ContentsMake sure that the package contains the following items. I

06 Stackable L2+/L3 Managed SwitchPlease keep a proper temperature and humidity in the equipment room. Too high/low humidity may lead to bad insulatio

07 Stackable L2+/L3 Managed Switchinstant current is strong enough to damage electronic devices, more effective lightning protection measures should b

08 Stackable L2+/L3 Managed SwitchThe Installation & Connection flow is shown as the following figure.StartInstall the switch to the specified pos

09 Stackable L2+/L3 Managed SwitchChapter 3 Installation3.1 Installing the Switch on a DesktopTo install the switch on the desktop, please follow th

10 Stackable L2+/L3 Managed Switch3. After the brackets are attached to the switch, use suitable screws (not provided) to secure the brackets to the

11 Stackable L2+/L3 Managed Switch2. If the protective cover has been installed on the power supply module slot of the switch, use a Phillips screwdri

12 Stackable L2+/L3 Managed Switch3. Hold the captive screws on the front panel of the interface card, and gently push the interface card in along th

13 Stackable L2+/L3 Managed SwitchInstallation2. Log on to the GUI of each switch, go to Stack→Stack Management→Stack Cong page to enable the stack m

14 Stackable L2+/L3 Managed SwitchLightning ProtectionChapter 4 Lightning Protection4.1 Cabling ReasonablyIn the actual network environment, you may

ICOPYRIGHT & TRADEMARKSSpecifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other br

15 Stackable L2+/L3 Managed Switch Requirements for the distance between Ethernet cable and other pipelines are shown in the table.Other PipelinesEth

16 Stackable L2+/L3 Managed Switch4.2 Connect to GroundConnecting the device to ground is to quickly release the lightning over-voltage and over-curre

17 Stackable L2+/L3 Managed SwitchNote: The figure is to illustrate the application and principle. The power cord you get from the package and the so

18 Stackable L2+/L3 Managed Switch4.4 Use Lightning ArresterPower lightning arrester and signal lightning arrester are used for lighting protection.Po

19 Stackable L2+/L3 Managed SwitchChapter 5 Connection5.1 Ethernet PortConnect the Ethernet ports of the switch to the network devices by RJ45 cable

20 Stackable L2+/L3 Managed SwitchConnect the console port of the device with your computer by the console cable as the following figure shown.Figure

21 Stackable L2+/L3 Managed SwitchPowerPS OKFaultPSM150-ACFigure 5-4 Power on via PSM150-ACNote: The gure is to illustrate the application and princ

22 Stackable L2+/L3 Managed SwitchFigure 5-6 Power on RPS150Caution: Make sure the power supply of RPS150 is cut off when connecting or disconnectin

23 Stackable L2+/L3 Managed SwitchChapter 6 Configuration6.1 Configure the Switch via GUINote: To log on to the GUI of the switch, the IP address of y

24 Stackable L2+/L3 Managed SwitchFigure 6-3 Main Page of the Switch6.2 Configure the Switch Using CLIYou can log on to the switch and access the CLI

IIRelated DocumentRelated Document The User Guide and CLI Reference Guide of the product are provided on the resource CD.To obtain the latest product

25 Stackable L2+/L3 Managed Switch3. The Connection Description Window will prompt as Figure 6-5. Enter a name into the Name field and click OK.Figur

26 Stackable L2+/L3 Managed SwitchFigure 6-7 Port Settings6. Type in the User name and Password in the Hyper Terminal window, the factory default val

27 Stackable L2+/L3 Managed Switch3. Click Start→Run to open the Run window.Figure 6-9 Open the Run window4. Type in cmd in the prompt Run window a

28 Stackable L2+/L3 Managed Switch6. Type in the User name and Password (the factory default value for both of them is admin) and press the Enter butt

29 Stackable L2+/L3 Managed SwitchAppendix A TroubleshootingQ1. What could I do if I forgot the username and password of the switch?1. Connect the

30 Stackable L2+/L3 Managed SwitchAppendix B Hardware SpecificationsItem ContentStandardsIEEE 802.3 10Base-T EthernetIEEE 802.3u 100Base-TX/100Base-FX

Website: http://www.tp-link.com Tel: +86 755 26504400 E-mail: [email protected]

IIIAudienceAudience This Installation Guide is for:Network EngineerNetwork AdministratorConventions Due to the similarity in structure of TP-LINK Je

IVContentsContentsChapter 1 Introduction ———————————— 011.1 Product Overview ...011.2 Appearance ...

01 Stackable L2+/L3 Managed SwitchChapter 1 Introduction 1.1 Product OverviewT2700G-28TQ/T3700G-28TQ is TP-LINK’s JetStream Stackable L2+/L3 Manage

02 Stackable L2+/L3 Managed SwitchLEDsLED Status IndicationPowerOn The switch is powered onOff The switch is powered off or power supply is abnormalFl

03 Stackable L2+/L3 Managed SwitchLED Status IndicationM1,M2OnAn SFP+ transceiver/cable is connected to the corresponding port of the Interface Card,

04 Stackable L2+/L3 Managed SwitchIntroduction Rear PanelThe rear panel of T3700G-28TQ is shown as the following figure.PowerPS OKFaultPSM150-AC100-2